Some rare mileage for some rare cargo

In November, I went to see family for a quick visit and to drop off some Christmas presents. It turned out to be a stroke of genius, as the postal strike scotched any mail delivery for Christmas shortly after my visit. I shared some details of my visit to Windsor on that journey, but there were other cool rail sightings and meets that weekend, including this incredibly lucky shot I snagged at Sarnia yard, as a CSX interchange move contained a most unexpected surprise.

I dropped by the yard late on a damp November morning, and it appeared at the outset that nothing was happening.The yard was largely quiet, except for the string of diesels idling at the refueling pad near the old roundhouse (more images from that to be shared in a later post).

Deep in the yard however, east of the Indian Road overpass, I could see something happening in the yard through the fog.

A CN yard engine was idling there for a few minutes before I spotted an engine with a yellow nose emerging from the refineries and industrial operations east of Indian Road. I was a little surprised, as I have never seen a CSX train this deep in Sarnia Yard. I will admit that my time spent at this yard is quite sporadic, so it might be quite common. Still, every time I see CSX in Sarnia yard, its transfer or interchange jobs are usually situated closer to the Via station in the west end of the yard. So this train being this deep in the yard was unusual, at least to me.

As the train began to slowly make its way toward the station and toward its home rails, I noticed something interesting with the power, to say nothing of an oddity at the end of the train. First, the power.

You can see from the rebuilt cab that this is not the typical GP38-2 unit that has been the power of choice in this area for decades. This unit, with a boxier cab is actually a rebuilt GP40, from what I could find online. I see it referred to as GP40-3 6547, part of a series of old geep rebuilds that have been rolling out of CSX's Huntington shops for years. From what I could read, the new cabs are safer and more resistant to crashes.The units are also equipped with new heating and air conditioning, new control systems, new positive train control technology and refurbished starters. Both units pulling this train were rebuilds. The new cabs remind me a bit of the old GP30 cabs, which were a bit more boxy than their peers of the time. I think I might like these rebuilds better if the cabs had curved corners like the GP30s, but that's just aesthetics.

You can see from the photo above that I tried to capture the CN unit deep in the yard in my shots. I love capturing multiple railways in one shot. 

Here's a better shot, below, of the power from the side. You can see the noses and the cabs both look much boxier than the old geeps, with the headlines in the nose recessed and other features that have been modernized. Not sure what I think of this new look. It's something different for CSX in Canada for sure.

So let's focus on the back end of the train, with that impressively large cargo bringing up the rear. I was pretty stunned to see anything on a CSX train other than tank cars and covered hoppers. Its customer base is almost exclusively industrial operations in the Chemical Valley in Sarnia and related industry south of the city. The goods it carries are always in a tank car or hopper.

A giant tarp-covered piece of industrial equipment sat on a 12 axle centre-depressed flatcar, buffered by two empty gondolas.This is a serious piece of machinery. But what is it? For that answer, I turned to the Chesapeake & Ohio Canadian Division Facebook group, where people much more knowledgeable than me had an answer. There is writing on the tarp, which says Do Not Hump. That seems obvious, but a good reminder nonetheless.

 

 

I was told this car was carrying a gas turbine used in stationary power generation. It was produced by GE Energy in Greenville, South Carolina. From there, it was shipped via Norfolk Southern to East Point, South Carolina.

 

At that point, CSX took over the move as it moved it to Wixom, Michigan. 

 

From there, it was taken through to Flint, Michigan via Lake State Railway (LSRC). 

 

From Flint, CSX power took it to Port Huron on CN H710. 

 

In Port Huron,CN brought it through the tunnel under the St. Clair River into Sarnia. 

 

From there, CSX took it back to home rails where it was delivered to a customer in Courtright, a small town south of Sarnia with a number of industrial customers in the area, including the CF Industries plant (formerly Tera, C-I-L).

 

UPDATE: The one missing piece of information that I could not figure out was the identity of the customer that needed the turbine. That was, until the day I put this post online and a Sarnia local told me the turbine was delivered to Greenfields Energy, a cogeneration plant beside the CF plant. There are a number of power generation facilities in the Sarnia area that are producing vast amounts of electricity, some of this generation being fed by the output of refineries themselves.

 

So that is the story of how this piece of industrial equipment found its way to Sarnia and how I just so happened to be around when it made its final move onto the CSX Sarnia Subdivision. Here's a going away shot below of the train making its way around the tunnel gantry on the rails curving by the roundhouse.

 

 And one more shot around the gantry.

 

 

I didn't stick around much longer, as I didn't want to keep my family waiting. But it was nice to have a few quiet moments at the rail yard and be treated to a surprise.

 

I have shot mainly CN and Via Rail photographs in the past few years, so it was nice to be able to capture something different. In a way, the fog and cloudy skies also helped, as they cut down on the shadows that usually plague shots in this area on clear days. Some good railway karma for a change.

I'll take it.